HD Tune Pro 5. It offers the strong capability to monitors all the dangerous possibilities that occur on your Hard Disk or SSD drives. USB sticks, memory cards, iPods, etc.
It works more precisely in command line interface OS. All it does is to scan through the whole system to check whether there are any errors. If that is not enough, HD Tune Pro will give you an option for what you need to do to rectify the errors. HD Tune Pro 5 Crack is one of the best ever application all over the internet. It is an incredible, easy to use and become a need for people around the world. A hard drive starts reading and writing at the outer tracks. By discarding the inner tracks the average speed will be higher.
It's important to note that short stroking will not make your hard drive faster. It will only instruct the operating system not to use the slow part of the drive. The performance tests of HD Tune Pro include an option to specify the test capacity. This allows to test the performance when short stroking is used. This option also allows for an easy comparison between drives with a different capacity.
By setting the short stroke capacity to a value which is equal or lower than the capacity of the smallest hard drive you will get a fair comparison.
For example: suppose you have a GB hard drive and you're using GB for the operating system and applications. If you want to install the same operating system and applications on a new, larger drive and want to see how it compares with the old hard drive you can set the stroke capacity to GB and test both hard drives. Enabling this option will simulate the behaviour on Windows Vista and Windows 7 systems. Older Windows typically use unaligned partitions which could result in poor performance with certain SSDs.
The Info tab shows the alignment for each partition on the disk. Usage 1. Select hard drive 2. Show temperature statistics 3. Current temperature display 4. Copy results or info to clipboard 5. Copy screenshot to clipboard 6. Save screenshot as png file 7.
Options 8. Minimize to tray 9. Exit program Select function Run at startup: automatically executes the program each times Windows starts.
Allow change of power settings during tests: certain processors reduce the performance in idle conditions. This may interfere with the test results.
By enabling this option the power settings will be ignored during the tests. Scan A: and B: drives: historically these drive letters were used for floppy drives. It is possible to assign these drive letters to hard drives.
Enabling this option allows the program to detect these drives. It's recommended to disable this option if these drive letters are not assigned because it will increase the time to start up the program. This may be convenient to differentiate identical drive models. Show drive letters: by checking this option all drive letters which are assigned to the drive are shown under the drive selector. Temperature statistics The current temperature can be shown on the main screen next to the drive selector, in the task bar and on the health page.
Detailed temperature statistics can be shown by pressing the temperature button next to the drive selector. The graph shows the temperature progress per minute. The current temperature is shown at the right position. Current temperature: current drive temperature Power cycle temperature: lowest and highest temperatures measured since start up All-time temperature: lowest and highest temperature ever measured with this drive Operating temperature limit: minimum and maximum temperature allowed when the drive is active.
Exceeding these limit may cause damage to the drive. Non-operating temperature limit: absolute temperature limits. Notes: 1. Show both units on screen: temperature will be shown in both Celsius an Fahrenheit on the main screen. Show temperature in taskbar: temperature will be shown on the taskbar.
If the temperature exceeds the specified limit a warning message will show up here. Font color - normal temperature: color of the temperature display when the temperature is below the critical value. Font color - critical temperature: color of the temperature display when the temperature is equal to or higher than the critical value.
Critical temperature: a warning will show up if the temperature equals or exceeds this value. Benchmark The benchmark function offers four different tests: 6.
Transfer rate The data transfer rate is measured across the entire disk surface default or across the selected capacity short stroke option. The X-axis shows the position in gigabytes gB. Both read and write transfer rate can be measured. To prevent accidental data loss, the write test can only be performed on a disk with no partitions. A newly bought hard disk usually doesn't have any partitions yet so this step is not necessary to run the write test.
Note: the data density at the outer tracks of a hard drive is higher than at the inner tracks. Reading or writing at the outer tracks will be done at a higher speed because the rotation speed is constant. A hard drive starts reading and writing at the outer tracks and moves to the inner tracks.
This can be seen in the transfer rate graph where the speed is the highest at the start of the test and decreases towards the end of the test. This will give the most accurate results but the test time will be very long. By choosing the partial test the transfer speed is sampled across the disk surface.
The test time and accuracy can be chosen by moving the slider. Block size: block size which is used during the transfer rate test. Lower values may give lower test results. The default value is 64 KB. Include raw graph values in log file: by enabling this option the graph values will be saved in the log file which can be imported in a spreadsheet. Access time The average access time is measured and displayed in milliseconds ms. The measured access times are shown on the graph as the yellow dots.
Multiple pass testing You can set the number of passes from 1 default to When performing write tests with SSDs it should be noted that the number of write cycles on these devices is limited therefore it's not recommended to run lengthy write tests on these devices. Note: if you use multiple pass testing you probably want to disable the 'Ask for file name and location' option from the Save options screen when you want to automatically save the results after each pass..
To avoid files being overwritten you can add the time format specifier ie. Changes: Health S. T and temperature display support for external drives Support for drives larger than 2 TB Supports up to 32 drives Advanced S.
HD Tune Pro is an extended version of HD Tune which includes many new features such as: write benchmark, secure erasing, AAM setting, folder usage view, disk monitor, command line parameters and file benchmark. Click here for more information and to download a trial version.
0コメント